Linksys Extender RE7000 Setup: Detailed Procedure
Is your network creating trouble for you? Are you looking for a solution that can give you a reliable network? Is there WiFi dead zone trouble? If the answer to all such questions is yes then you reach the absolutely right page. The perfect solution for all your network troubles is to set up linksys range extender devices. There are several models available in the market but linksys extender RE7000 is the best of all of them. This range extender is known for its design and latest technology. The device has the capability to offer dual band frequency that helps in eliminating WiFi zones from your current network.
Linksys extender re7000 setup is not a big deal if you know the correct process. In the further section of the article you will find the detailed process using WPS and web based methods. Check out the process to configure your device.
Linksys RE7000 Setup: Requirements
Before jumping into the set up method you have to assure that you have everything required in the setup process. Here is the list of requirements:
If you have all such requirements handy then you can proceed with the installation of the device hardware and then set up.
Linksys RE7000 Setup: Installation
Linksys RE7000 Range extender device installation process involves three simple steps. Check out the steps and follow the Linksys Extender RE7000 Setup guide after installation of the hardware of the device.
Unbox
To install the linksys extender RE7000 hardware you have to unbox it properly. Make sure your device is not physically damaged. Verify that the box contains ethernet cable and setup guide along with the range extended device.
Place
The second step is placement. To keep the device you don’t need a separate place. This range extended device is a wall plug compact design device. You just need to look for a location to plug the device in the wall socket.
Power
Once the location where you have to turn on the device is decided you have to plug the device into the wall socket. Wait for the device power button to turn on. When the LED gets stable you can initiate the setup using any of the below given methods.
Linksys RE7000 Setup: WPS
To pursue with the WPS method you don’t need any additional device to connect the router with the extender. Here are the steps which you have to follow to complete the configuration.
Press Router’s WPS
First of all you have to press the WPS button on the router device. Hold the button for about 5 to 10 seconds and then release it when the WPS LED starts blinking.
Press Extender’s WPS
Thereafter you have to do the same with the WPS button on the extender device. When it’s done you have to just wait and watch your extended device behaviour. When the device boots up properly and its LED starts displaying solid green colour it signifies that your linksys extender RE7000 setup is done.
Relocate
Relocate the extended device to a location somewhere in the midway of the placement of your router and the area where you are facing a dead zone problem.
Linksys RE7000 Setup: Web
Doing configuration using the web base set up is a little time consuming and requires a computer or laptop device or a smartphone device to pursue. Below is the detailed procedure you have to follow:
Connect To Extender’s Network
On your smartphone or computer, go to WiFi settings and connect to the default “Linksys Extender Setup_XXX” network, where “XXX” represents the last three digits of your extender’s MAC address. You may also use an Ethernet cable to connect directly.
Launch Web Surfer
Open any web browser installed in your device to initiate the setup. The browser you can use must be an updated version of it. Also there should be no cache or cookies.
Access Setup Page
Get access to the setup page using the web address or default IP. Mention the standard account information to reach the dashboard.
Connect To Router’s Network
To connect the router you need to enter the router’s SSID and password on the screen.
Create SSID & Password For Extender
Once connection is done you have to create the SSID and password for your extenders network to keep it secure.
Update Firmware
Check for the firmware update, if a new version is available first.
Finalize Setup
Save all the changes you have made to the settings and reboot the device.
Relocate
If needed then you can relocate the device in a midway to boost its performance.
Connect Us
If you find any step difficult or got stuck when doing the linksys extender RE7000 setup then connect our expert team.
