How To Resolve Connectivity Issues With Linksys Velop Mesh Systems

Linksys velop mesh systems are widely used to enjoy seamless network connectivity in larger homes or multistory buildings. Linksys velop mesh system contains the latest technology devices. Sometimes even these devices encounter connectivity issues. Troubleshooting the Connectivity Issues With Linksys Velop Mesh Systems is a very simple task. In this article below you will find the troubleshooting guide to resolve the issue on your own, whether you’re experiencing slow speeds, dropped connections, or nodes going offline. 

Restart Your Linksys Velop Mesh System

Restart your linksys velop mesh system to resolve the connectivity issues. It is the simplest and easiest way to troubleshoot the problem. Along with the velop node you have to restart your source device also. To restart the system you have to follow the below specified steps: 

• Unplug the modem and all Velop nodes.
• Wait for about 30 seconds.
• Plug in the modem first 
• Wait for it to fully boot up.
• Power on the primary node 
• Then child nodes.

This reset can often resolve temporary glitches and re-establish lost connections.

Check Internet Connection From Source 

Before assuming that the issue is because of the velop system you should verify whether your internet service is working properly from the source device or not. Checking the connection by using an ethernet cable. Steps you have to follow to check the internet connection from the source device are as under: 

• First of all you have to take an ethernet cable which is working properly. 
• Connect the computer or laptop device with the modem using the ethernet cable. 
• Now check if the internet is working or not by browsing websites or playing online videos. 
• If there is a problem then you have to connect your internet service provider. 

This will help you determine whether the issue is with your velop system or from the service provider. 

Relocate The Velop Nodes

Improper placement of Velop nodes is a frequent cause of connectivity issues. Nodes must be within optimal range of each other to ensure a strong backhaul connection. You have to relocate the velop nodes to trouble shoot the connectivity issue you are facing with the system. 

• Place the primary node near the modem in a central location.
• Position child nodes within two rooms or approximately 30-50 feet of the primary node.
• Avoid placing nodes near thick walls, metal objects, or electronic devices that might cause interference (e.g., microwave ovens, cordless phones).

Update Firmware

Next trouble shooting tips to resolve the connectivity issue with linksys Velop mess system is firmware updation. Updated firmware of linksys velop nodes can create problems. To improve performance and security of the system the manufacturer releases firmware updates regularly. Update your device firmware by follow the given process: 

• Open the Linksys app or log in via the web interface at https://www.linksyssmartwifi.com.
• Navigate to Network Administration and then Firmware Update.
• Check for available updates and follow the prompts to install them.

Ensure all nodes are updated for consistent performance.

Reconfigure The System After Reset

If the above specified steps don’t resolve your issue then you can perform factory reset and then start a fresh configuration that might help you. To reset the linksys velop mesh system and configure it again you have to follow the steps mentioned here:

• Initiate the reset by cold and press the recent button on each node of the velop system.
• You have to hold the button until the light turns red. 
• You have to perform a reset on each node connected in the system one after the other. 
• Remember to reset the primary note in the last. 
• Once you reset all the devices you have to configure them again using the linksys app.

Eliminate Network Interfering Devices

WiFi signals are sensitive to interference. This causes connectivity issues with Linksys Velop mesh system. To resolve the problem you have to minimize the interference. 

• Keep your Wi-Fi router and nodes away from Bluetooth speakers, baby monitors, and microwave ovens.
• Change the wireless channel in the router settings if too many nearby networks overlap.
• Enable Auto Channel in the Linksys app to allow automatic optimization.

Conclusion

The linksys velop mesh system is designed to offer seamless network coverage across the space. Occasionally connectivity issues might arise with the velop system. Resolving the connectivity issues is very simple by following the above specified troubleshoot. In case even after following the above specified trouble shoot your issue doesn’t get resolved then you can connect our technical team for help. We are just a call away from you. Call on the below given number and get the solution to your problem instantly.